How Far Can Something Hang Out of a Truck

Download Article

Download Article

Decorating your cement walls can exist tricky if you lot don't have the right hardware. Luckily, there are some great options that are inexpensive and readily available. Choose adhesive hooks for lightweight items upwardly to viii pounds (three.6 kg), hardwall hangers for objects weighing up to 25 pounds (eleven kg), and masonry anchors for your heaviest decorations exceeding 25 pounds (11 kg).

1. 1

   Choose adhesive hooks for objects up to eight pounds (iii.6 kg). These hooks take agglutinative backings that stick to walls, so y'all don't have to put a pigsty in the wall. Weigh the object get-go and then yous can pick a hook that will properly support it.^[i]

   • Adhesive hooks come in various sizes and should say how many pounds they will hold. The largest of these hooks hold 8 pounds (iii.6 kg) and the smallest are rated for just 1 pound (0.45 kg) of weight.
   • Employ 2 hooks for actress support if your item has a wire or two hooks on the back.

2. 2

   Make clean the wall with rubbing alcohol for a ameliorate hold. Use a clean rag or paper towel and some rubbing alcohol to scrub the surface area of any debris. This will ensure that the adhesive will stick firmly to the wall.^[two]

   • If you don't have rubbing alcohol, you tin can utilize some warm soapy water to clean the wall. Rub the spot dry out after cleaning.

   Advertisement

3. 3

   Make a small-scale pencil marker where you want the center of your hook to be. If the item you'll exist hanging has a wire hanger on the dorsum, exist sure to consider the length of the slack. Examination this by pulling the center of the wire tight toward the top of your object. Measure from the bottom of the object to where the wire catches.

   • If you are using two hooks for an object with ii hangers on the back, make sure to measure out the distance betwixt the two hangers to brand your marks on the wall.
   • If you are using ii hooks for a wire hanger, measure the width of the object yous are hanging and divide that number by 3. Your marks on the wall should be that altitude autonomously.

4. iv

   Remove the liner from the adhesive strip and braze information technology to the dorsum of the claw. If your hook's adhesive strip is non already on the back of the claw, peel the liner off i side of the strip. Line information technology upwardly to the dorsum of the hook and printing down.

   • Some adhesive hooks come with the agglutinative already affixed to the back. Skip this footstep and move on to the next if that's the case with the adhesive hook yous accept.

5. 5

   Press the adhesive side of the claw to the wall for 30 seconds. Remove the paper lining on the back of the hook, line it upwardly direct, and press the hook firmly onto the wall. Concord for thirty seconds and release.

6. vi

   Allow the adhesive to dry 30-60 minutes. Once the adhesive has dried, hang your items from the hook(south).

   • If your item pulls the adhesive hook off the wall fifty-fifty afterwards yous've waited, bank check to make certain y'all've used a hook that is appropriate for the weight of your item.

   Advertisement

1. 1

   Buy hardwall hangers to use for items that weigh upwardly to 25 pounds (eleven kg). Hardwall hangers are fabricated specifically for cement and brick walls. Each hanger comes with four sturdy pins that will anchor the base of the hook to the wall.

   • Yous will need a hammer to install hardwall hangers.
   • Employ 2 hardwall hangers to hang 1 object if you lot want actress support and take hanging hardware that will accommodate this.

2. ii

   Mark the spot on the wall where you want the hanger to be placed. If the item you are hanging has a wire-hanger in the back, exist sure to consider the slack when determining where you lot want it to hang. Exam this past pulling the heart of the wire tight toward the height of your object. Measure from the bottom of the object to where the wire catches.

   • If you lot are using two hardwall hangers, either measure the distance between the 2 hooks on the back of your object or measure the width of the object yous are hanging and divide that number past 3. Ane of these two methods will determine how far apart you make your marks on the wall.

3. iii

   Hammer the pins through the holes provided. Line the middle of the base upwardly with the marking you've made. Hold the hanger still with i hand and tap all iv pins in halfway with the hammer. Release your hold on the hanger and bank check that the hook is in the correct position. Stop past hammering the pins flush to the hook.

   • To avert getting your fingers hobbling, keep your initial taps very light. Once you feel that the pin has taken hold in the wall, release your agree on the pivot and strike the hammer directly on the pinhead to finish.

4. 4

   Loop the wire or hanging hardware of your detail onto the hook. Stand dorsum to brand certain it is hung straight. Make any adjustments needed and relish.

   Advertisement

1. i

   Choose masonry anchors to hang objects over 25 pounds (11 kg). These anchors are generally plastic and come with the screws that you insert into them. You volition need a drill and a masonry scrap the aforementioned size as the anchors.^[3]

   • Y'all tin purchase masonry kits that include anchors, screws, and the right size masonry bit.
   • For added support, employ 2 masonry anchors to hang 1 particular.

2. 2

   Employ a hammer drill for the all-time results. A standard electrical drill will work with a masonry bit, but information technology will be ho-hum-going and at that place is the adventure yous volition create a hole much larger than yous desire. Rent or borrow a hammer drill if you can.^[iv]

   • You can hire a hammer drill at your local hardware store, Lowe'south, Home Depot, or a tool rental shop. Telephone call ahead to brand arrangements.

3. 3

   Drill a pigsty to accommodate the anchor. Measure advisedly and marking the spot for your anchor. Place the scrap on the spot you've chosen. Make certain your grasp is firm and cheque to see that the bit, the drill shaft, and your arm are all parallel to the flooring. As you drill, press firmly into the wall and maintain your position.^[five]

   • Employ a slower speed when drilling into cement walls for the best results.

4. four

   Tap the anchor in the hole until it's flush with the wall. The fit should be snug but not so tight that you have to hammer hard. If you lot find that the hole is too small, re-drill using a slightly larger flake.

5. 5

   Identify the spiral into the anchor. Utilize a screwdriver or the screw bit on your drill to tighten it down. Stop before the screw is flush, and so there is space to suit the wire or hanging hardware. Hang your object, adjust information technology until information technology is straight, and relish.^[6]

   Advert

Add together New Question

• Question

  How can you hang something on a cement wall?

  

  Jason Phillip is a handyman specializing in mounting and hanging objects onto walls. With over 5 years of feel professionally mounting and installing objects through his company, Jason's Handyman Services, Jason's work includes working with mounting window Air conditioning units, designing art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Tiptop Pro" every year since 2022 by Thumbtack for being one of the highest-rated, well-nigh popular professionals on Thumbtack.

  

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Make sure to read and follow the operating instructions provided with your drill before using information technology.

• Protect your eyes when yous are drilling. Consider wearing goggles or safety glasses.

• Apply a stud finder with a wire tracer setting to make sure you are not drilling near any live electrical wires.

Advert

Things Yous'll Demand

• Adhesive hooks of pick
• Rubbing alcohol
• Clean rag or paper towel
• Pencil
• Record measure

• Hardwall hangers and pins
• Hammer
• Pencil
• Record measure

• Masonry anchors and screws
• Masonry bit the aforementioned size equally the anchors
• Hammer drill or standard electric drill
• Pencil
• Tape measure

Near This Article

Commodity Summary Ten

If you want to hang something from a cement wall, try using adhesive hooks so y'all don't accept to put a hole in the wall. Choose a hook that's rated to hold more the weight of the object you are hanging. When you're ready to hang the hook, clean the surface of the wall with rubbing alcohol, then skin off the backing from the claw and press information technology against the wall for 30 seconds. Permit the adhesive to dry for 30-hr. If yous want to hang things using hardwall hangers, read on!

Did this summary assist you?

Cheers to all authors for creating a page that has been read 202,921 times.

Did this commodity assistance you?

davisbidisty.blogspot.com

Source: https://www.wikihow.com/Hang-Things-on-a-Cement-Wall

Share this post